Jamii at 20:59, 4 June 2008

2008-06-04T20:59:50Z

← Older revision		Revision as of 14:59, 4 June 2008
Line 1:		Line 1:
	===Configuring the Actiontec 1520 (the white model) for a WAN static or		===Configuring the Actiontec 1520 (the white model) for a WAN static or public subnet.===
	public subnet.===
	Article:181		Article:181
	Created:2002-11-20 13:10:09		Created:2002-11-20 13:10:09

Jamii: /* Resolution */

2008-06-04T20:59:31Z

Resolution

← Older revision		Revision as of 14:59, 4 June 2008
Line 12:		Line 12:

	====Resolution====		====Resolution====
	Static WAN IP		=====Static WAN IP=====
	-------------		-------------

Line 21:		Line 21:


	Public Subnet		=====Public Subnet=====
	-------------		-------------

Line 51:		Line 51:

	You are done.		You are done.


	====Related KB articles====		====Related KB articles====
	[[KB 175]] Configuring the Actiontec 1520 (the white model) to use NAT		[[KB 175]] Configuring the Actiontec 1520 (the white model) to use NAT

Jamii: New page: ===Configuring the Actiontec 1520 (the white model) for a WAN static or public subnet.=== Article:181 Created:2002-11-20 13:10:09 Categories: DSL ====Question or Symptom==== How do ...

2008-06-04T20:59:06Z

New page: ===Configuring the Actiontec 1520 (the white model) for a WAN static or public subnet.=== Article:181 Created:2002-11-20 13:10:09 Categories: DSL ====Question or Symptom==== How do ...

New page

===Configuring the Actiontec 1520 (the white model) for a WAN static or
public subnet.===
Article:181
Created:2002-11-20 13:10:09
Categories:
DSL

====Question or Symptom====
How do I configure my Actiontec 1520 (the white model) Wireless-Ready
DSL Gateway to use a static WAN IP or public subnet?

====Resolution====
Static WAN IP
-------------

There is no difference in the configuration of the Actiontec for a dynamic or
static WAN IP. The assigning of the static IP takes place upon login.
Configure using the SWCP Knowledge Base article 175,
Configuring the Actiontec Wireless-Ready DSL Gateway (ethernet and NAT).

Public Subnet
-------------

If you have a public subnet (2 or more public IP's), there are a few differences.

First, complete the instructions in the SWCP Knowledge Base article 175,
Configuring the Actiontec Wireless-Ready DSL Gateway (ethernet and NAT).

Next, open your web browser of choice, and surf to http://192.168.0.1. This
will take you to the web interface for configuring the router. Click
"Setup/Configuration."

There will be sidebar on the left. Click "Advanced Setup."

Click the "Begin Advanced Setup" button.

Again,in the left-hand sidebar, click "LAN IP Address."

Enter the first IP from your public subnet.

Click "Next" through the next several screens unti you reach the one with the
heading "NAT."

Click the "Off" radio button.

Click "Next" until you reach the screen with the heading "Save and Restart."

Click the button "Save and Restart."

You are done.

====Related KB articles====
[[KB 175]] Configuring the Actiontec 1520 (the white model) to use NAT

KB 181 - Revision history

Jamii at 20:59, 4 June 2008

Jamii: /* Resolution */

Jamii: New page: ===Configuring the Actiontec 1520 (the white model) for a WAN static or public subnet.=== Article:181 Created:2002-11-20 13:10:09 Categories: DSL ====Question or Symptom==== How do ...