View source for KB 265

===How to configure a Broadmax Linkmax Router the telnet way.===
 Article:265
 Created:2003-11-14 14:45:52
 Categories:
   DSL

====Question or Symptom====



====Resolution====
The Broadmax router has both a web based GUI and a telnet interface. Both can be
used to configure the device. Here is how to configure the device thru the telnet interface.
  
   1. Configure your ethernet device to have an ip address on the same subnet as
      the Broadmax, by default the Broadmax's ethernet ip address is
      192.168.0.1.
   2. Telnet to the Broadmax. You will be prompted fro username and password,
      the default's are broadmax/broadmax.
   3. Issue the following commands:
  
       -------------------------------------------------------------------
       BASIC CONFIG
  
       modify bridge mode disable
           
       modify bridge mode wan2wan disable
           
       create atm vc intf ifname aal5-1 vpi 0 vci 32 vcmux enable
           
       create ppp intf ifname ppp-0 start lowif aal5-1 droute true PPOA
       usedhcp true
  
       create ppp security ifname ppp-0 PAP login USERNAME passwd PASSWORD
  
       -------------------------------------------------------------------
       DHCP SERVER
  
       create dhcp server pool poolid 0 start-ip IP end-ip IP mask NETMASK
       dname DOMAIN gwy GATEWAY dns DNS1 sdns DNS2 enable
  
       modify dhcp server cfg enable
       commit
  
       reboot
 
       -------------------------------------------------------------------
       ROUTED SUBNET CONFIG
  
       modify bridge mode disable
  
       modify bridge mode wan2wan disable
           
       create atm vc intf ifname aal5-1 vpi 0 vci 32 vcmux enable
  
       create ppp intf ifname ppp-0 start lowif aal5-1 droute true PPOA
       usedhcp true None
  
       create ppp security ifname ppp-0 PAP login USERNAME passwd PASSWORD
  
       modify ethernet intf ifname eth-0 ip ETH_IP mask NETMASK usedhcp false
  
       modify nat global disable
  
       commit
  
       reboot
  
       ------------------------------------------------------------------
       CHANGING ETH ADDRESS
  
       modify ethernet intf ifname eth-0 ip ETH_IP mask NETMASK usedhcp false
  
       commit
  
       reboot
  
       ------------------------------------------------------------------
       CHANGING PASSWORD
  
       passwd broadmax         
  
       commit
  
       reboot
  
       ------------------------------------------------------------------
       CHANGING FROM NAT TO ROUTED
  
       delete ppp intf ifname ppp-0
  
       create ppp intf ifname ppp-0 start lowif aal5-1 droute true PPOA
       usedhcp true None
  
       modify ethernet intf ifname eth-0 ip ETH_IP mask NETMASK usedhcp false
  
       modify dhcp server cfg disable
  
       modify nat global disable
  
       commit
  
       reboot
  
       ------------------------------------------------------------------
       PORT FORWARDING (!!THESE THREE LINES ARE ONE LINE WRAPPED FOR SANITY!!)
  
       create nat rule entry ruleid NUMBER rdr prot PROT ifname ppp-0
       lcladdrfrom INT_IP lcladdrto INT_IP destportfrom num EXT_PORT 
       destportto num EXT_PORT lclport num INT_PORT
  
       commit
  
       reboot
  
       The NUMBER field can be any number above 3. To see what is currently 
       defined, issue:
  
       get nat rule entry
  
       To delete:
  
       delete nat rule entry ruleid NUMBER
  
       ------------------------------------------------------------------
       NAT
  
       To get NAT satus:
  
       get nat global
  
       To Disable:
  
       set nat global disable
  
       To Enable:
  
       set nat global enable

====Related KB articles====
  [[KB 276]] I jacked my BroadMax router, now what? Or configuring the broadmax
     router via the web interface.

  [[KB 286]] Port Forwarding the Broadmax via the web interface.